PRINT

        ANALYSE\PRINT [Arg] [/OUTPUT File] [/TABLE File]

    PRINT  enables  one to list some parameters in a GreG compatible format.
    Arg is an optional argument to precise what to print :

      FIT       Results of profile fits in current method

        The information written is (1) the number of lines fitted,  (2)  the
        observation  number,  (3,4)  the  offsets  in  current  angle units,
        (5,6,...) fit results of the current method in the same order as  in
        DISPLAY command. For the Gauss Method, this order is: (5) Line Area,
        (6) its incertainty (7) Position (8) incert. (9) Width (10)  incert.
        (11) Intensity (12) Base RMS (13) Line RMS.

      AREA               Integrated area computed by BASE

        The  information  written  is  (1) the observation number, (2,3) the
        offsets in current angle units, (4,5) Area and rms noise.

      AREA v1 v2 v3 ...       Area in velocity ranges

        Area in velocity ranges v1 to v2 and v2 to v3, ... etc.  The  infor-
        mation  written  is (1) the observation number, (2,3) the offsets in
        current angle units, (4,5,...) the areas.

      CHANNEL List              List of channels

        The list in the same format as the FOR-NEXT loop. Up to 15  channels
        at a time may be listed. The information written is (1) the observa-
        tion number, (2,3) the offsets in current angle units, (4,5,...) the
        channels value.

      MOMENT m1 m2 ...       Moments of the observations

        The  moments (area, mean velocity, width) are computed in the inter-
        vals [m1,m2] [m3,m4] etc... Current unit is used.   The  information
        written  is (1) the observation number, (2,3) the offsets in current
        angle units, (4,5,6) area, position, width, (7,8,9) etc...

      POINTING           Pointing fit results

        Results of CONTINUUM method fit are printed in a format  adapted  to
        pointing  constants  measurements.  The information written is (1,2)
        The observation and scan number, (3)  a  code  for  scan  direction,
        (4,5)  Azimuth  and  Elevation  in degrees, (6) Time in hours, (7,8)
        Collimation and error along drift direction, (9,10) the antenna num-
        ber and station code, (11,12) Width and error, (13,14) Intensity and
        rms noise, (15) Source name.

      FLUX               Flux measurements results

        Results of CONTINUUM method fits printed in a format adapted to flux
        measurements.  The  information written is (1,2) The observation and
        scan number, (3) a code for scan direction, (4,5) Azimuth and Eleva-
        tion  in  degrees, (6) Time in hours, (7,8) Position and error along
        drift direction, (9) the antenna number, (10,11)  Width  and  error,
        (12,13) Intensity and rms noise, (14) Image gain ratio, (15,16) Sig-
        nal and Image frequencies, (17) Source name, (18) Observing date.

    /OUTPUT File
      Write the results in a formatted file named File  instead  of  on  the
      screen. The file is suited for later processing by GreG, in particular
      for contour maps.

    /TABLE File
      Write the results in a table named File. This table can  also  be  ac-
      cessed by GreG, in a much faster (50 times) way than a formatted file.
      Tables can also handle many more columns  than  formatted  files,  and
      they  are not limited in precision by the formatting. Mathematical op-
      erations can be done directly on the table columns.  However  the  FIT
      results cannot be written to a table.